| Capacity | 3kVA, 6kVA, 10kVA, 15kVA, 20kVA, 30kVA, 60kVA, 100kVA, 150Kva |
| Input | Three Phase: 200Vac (L-L),208Vac (L-L),380Vac (L-L), 400Vac (L-L), 415Vac (L-L) 440Vac (L-L)±20%. or volt value as per customized.3 Phase Delta or 3 Phase 4 Wire Wye type |
| Frequency: 40 - 70hz. | |
| Output Volt. | DC28.5VDC or 270VDC, voltage could be adjusted in a wide range. |
| Output Amperes. | 50A,100A, 200A, 300A, 400A, 500A, 600A, 800A, 1000A, 2000A |
| Voltage regulation / stability | +/-1% |
| Power Factor | ≧0.85 |
| Efficiency | ≧85% |
| Ripple | Less than 150mV, max 250mV (rms) |
| Display | VFD / LCD display, Volt. Amperes, and Power |
| Overload | 125% 10 min, 150% 60s, 200% 10s |
| Protection | O/V, under Voltage, current limiting, Over heating,Short Circuit Protections |
| Working Condition | Ambient Temp. -10℃ - 50℃ |
| Humidity: 10 - 95% | |
| Altitude ＜ 1800 meters | |
| Standard | |
| Mean Time Between Failure | 30,000H |
| Mean Time to Restoration | < 30 min |
| Standard |
EN61000-6-2:2005 GJB152A-97 Electromagnetic Emission and Susceptibility Requirements for Military Equipment and Subsystems
MIL-STD-704F
|
The following table applies to the ADCW 28.5 V DC configurations in the Ver.25 export catalogue. Confirm a separate model datasheet for other output voltages mentioned in the original description, including 270 V DC.
| Item | Ver.25 catalogue data |
|---|---|
| Model example | ADCW-28600 |
| Nominal three-phase AC input | 208, 380, 400, 415, 440 or 480 V AC, depending on configuration |
| Input voltage tolerance | ±15% |
| Nominal input frequency | 50 or 60 Hz. Catalogue input frequency tolerance is 40–70 Hz. |
| Input power factor | ≥0.9 |
| Nominal DC output | 28.5 V DC |
| DC voltage adjustment | 20–32 V DC |
| Listed output current ratings | 300, 400, 500, 600, 800, 1,000 and 2,000 A |
| Voltage regulation | Line regulation ±0.5% FS. Load regulation ±1% FS. |
| Ripple and efficiency | Ripple ≤0.25 V. Overall efficiency ≥93%. |
| Display and communications | 0.1 V and 0.1 A display resolution. RS232 / RS485 with Modbus protocol. |
| Overload rating and duration | 125% for 10 min, 150% for 60 s and 200% for 30 s |
| Enclosure and operating environment | IP20, IP21 or IP54 according to configuration. Catalogue operating temperature −20 to 50 °C and humidity 10–95%. |
Which current should I specify for maintenance? Give the aircraft type, ground operation, site supply and required continuous current. The final continuous rating is confirmed for the selected model and its duty.
What information is needed for engine starting? Provide the aircraft’s peak starting current, duration and start sequence, along with the required cable length and connector. Use the selected model’s datasheet to confirm peak capability and duration.